Tools For Tiling
For fixing finished tiles, a plumb line and soul level are required for setting out the parts to ensured verticals and horizontals; some slim wooden checks are relied upon to help the least tile pushes as work propels; an indented tile stick spreader, a tile shaper, a couple of forceps and a wipe are what's inexorably fundamental. A tile-culting move will restore cutting straight lines; a tile saw can cut twists. Use a sharp edge for cutting fitting tiles; a few scissors or gets for metallic tiles; a glass shaper for mirror tiles and a square help and club hammer for crushed copy square and stone tiles if key.
Finding the level
The going with stage is to develop a reasonably level datum line around the room. Never trust a keeping up a key decent ways from board to be level more than likely using a maintaining a strategic distance from board as a level will decode that even lines won't be unfathomably level, and as tiling is done by returning to the starting stage the lines won't mastermind.
Drawing a line on the divider flawless round the live with a strip and a spirit level, to relate with the base edge of the most diminished piece of whole tiles. Along this line stick dainty authenticates the divider with square work nails; don't drive the nails home, since the sheets ought to be prised off yet again. In the occasion that nails can't be collided with the divider (an old tile divider, state) get the strips level by putting them on little stores of tiles. Next, using a spirit level or plumb line, draw a guaranteed vertical line on the divider at the point where tiling is to start - at the edge of the last vertical zone of whole tiles (on a strong divider) or concurring with the essential line of whole tiles near a window or way opening. A vertical secure can be nailed along this vertical line as an extra guide.
Fixing the tiles
Spread the tile stick on the divider with a scored spreader, covering a space of around one square meter at some passionate minute. Draw the spreader over the bond by pressing it down with the objective that the teeth contact the mortar surface underneath; the indents by then certification that the paste is spread to a standard criticalness. Separate the fundamental tile on the even secure, line its edge up with the vertical standard and press it mindfully yet unequivocally to the divider. Association the going with tile near the first, with the spacer passes on in a general sense coming to, and watch that its face is level with that of the standard tile. If the tiles don't have spacer passes on, use matchsticks or tile spacers between the tiles. Continue with the section until the edge of the region is rehearsed, by then set a second, third and fourth line, checking all the time that the tiles are really agreed with each other. Spread cleverly security along the space over the divider secure, continuing to consolidate whole tiles until the zone is attested or until an impediment, for instance, a passage or window sill is come to. From lime to time, use a spirit level on a strip to watch that the tiles are amazingly level.
Cutting tiles
At a window sill, it isn't astounding to tile the reveals and the edge itself with round-edged or affirmed edged tiles which spread the edges of the tiles on the substance of the divider. So the going with work is to check and cut the bits of tile to go on the divider underneath the window sill. Scratching the tile with a felt pen or Chinagraph pencil, and after that score the protected substance of the tile with a tile shaper. To snap the tile along the scored line, either press down on cither side of the line over a straight edge, or use a couple of tile snappers with picked jaws. If the cut edge is amazing, use a tile scouring stone (a sort of coarse beating looking like pumice stone) or an oilstone hosed with water to smooth the tile edges. To cut a L-shape, make one cut with a tile saw and the other with a tile shaper. Cut and fit the constrained bits of tile that packaging the window opening; by then fit the round-edged tiles inside the reveal, butting the round edge agreeably over the edges of the cut pieces on the substance of the divider. Complete the tiling of the reveals with whole tiles or cut pieces as central.
Tiling over segment and window openings
Fix sponsorship acknowledges over section and window openings to pass on the principal zone of cut tiles over the opening. These, and the fundamental assistance affirms close keeping up a basic not too bad ways from weight up level, must be left set up until the strong has had space plan astute to set - for in any occasion 12 hours, and in a perfect world for 24 - or the tiles will sneak by their own one of a kind special excellent weight. When they have been cleared, cut and lit the edges pieces expected to complete the tiling, buttering paste on to the back of each piece before crushing it into spot. To cut edge pieces turn the tile back to front, mark two on the sides of the tiles for the circumstance of the score line and subsequently turn the tile over, score it and break it.
Turning a corner
When turning a corner, fix the crucial vertical line of whole tiles on the going with divider before filling in the cut pieces in the point. With arranged tiles, keep some comparability to structure learning by using cut bits of a close-by tile to fill the openings on each side of the point.
Changes in level
When tiling over existing tiles that stop more than almost the entire far up the divider tile flooring, there is a limit in level to change as indicated by. If the movement is basically nothing, fix the last area of whole tiles with their top edges direct over the improvement, and fill the opening behind with mortar, empowering this to set before keeping fixing whole tiles over the improvement. Steps more than about 12mm basic can't be covered as such. With these you can either stop tiling at the most raised explanation behind the old tiles and fulfillment off the most fundamental inspiration driving the tiling with a hardwood lipping or slips of cut tile set on a level plane, or present a visual break as a dainty wooden rack or the quadrant tiles sold for fitting in the corner between a shower and the divider. The choice is to bring the upper bit of the divider up to a proportionate level - with sheets of MDF or plasterboard, for example.
Grouting
When tiling is done, the going with work is to fill the openings between the tiles with grout. Apply it with a plastic scrubber or a wipe, obliging it well into the gaps between the tiles. Expel riches grout from the covering as mix activates and cloak the grout lines with a sprinkled finger or a little balanced smooth - a used sweet stick is flawless. Make the basic advances not to leave grout to set on the covering as it may be difficult to get off. Unequivocally when the grout has set, clean the tile surface with a perfect, dry surface to finish the progress.
Finding the level
The going with stage is to develop a reasonably level datum line around the room. Never trust a keeping up a key decent ways from board to be level more than likely using a maintaining a strategic distance from board as a level will decode that even lines won't be unfathomably level, and as tiling is done by returning to the starting stage the lines won't mastermind.
Drawing a line on the divider flawless round the live with a strip and a spirit level, to relate with the base edge of the most diminished piece of whole tiles. Along this line stick dainty authenticates the divider with square work nails; don't drive the nails home, since the sheets ought to be prised off yet again. In the occasion that nails can't be collided with the divider (an old tile divider, state) get the strips level by putting them on little stores of tiles. Next, using a spirit level or plumb line, draw a guaranteed vertical line on the divider at the point where tiling is to start - at the edge of the last vertical zone of whole tiles (on a strong divider) or concurring with the essential line of whole tiles near a window or way opening. A vertical secure can be nailed along this vertical line as an extra guide.
Fixing the tiles
Spread the tile stick on the divider with a scored spreader, covering a space of around one square meter at some passionate minute. Draw the spreader over the bond by pressing it down with the objective that the teeth contact the mortar surface underneath; the indents by then certification that the paste is spread to a standard criticalness. Separate the fundamental tile on the even secure, line its edge up with the vertical standard and press it mindfully yet unequivocally to the divider. Association the going with tile near the first, with the spacer passes on in a general sense coming to, and watch that its face is level with that of the standard tile. If the tiles don't have spacer passes on, use matchsticks or tile spacers between the tiles. Continue with the section until the edge of the region is rehearsed, by then set a second, third and fourth line, checking all the time that the tiles are really agreed with each other. Spread cleverly security along the space over the divider secure, continuing to consolidate whole tiles until the zone is attested or until an impediment, for instance, a passage or window sill is come to. From lime to time, use a spirit level on a strip to watch that the tiles are amazingly level.
Cutting tiles
At a window sill, it isn't astounding to tile the reveals and the edge itself with round-edged or affirmed edged tiles which spread the edges of the tiles on the substance of the divider. So the going with work is to check and cut the bits of tile to go on the divider underneath the window sill. Scratching the tile with a felt pen or Chinagraph pencil, and after that score the protected substance of the tile with a tile shaper. To snap the tile along the scored line, either press down on cither side of the line over a straight edge, or use a couple of tile snappers with picked jaws. If the cut edge is amazing, use a tile scouring stone (a sort of coarse beating looking like pumice stone) or an oilstone hosed with water to smooth the tile edges. To cut a L-shape, make one cut with a tile saw and the other with a tile shaper. Cut and fit the constrained bits of tile that packaging the window opening; by then fit the round-edged tiles inside the reveal, butting the round edge agreeably over the edges of the cut pieces on the substance of the divider. Complete the tiling of the reveals with whole tiles or cut pieces as central.
Tiling over segment and window openings
Fix sponsorship acknowledges over section and window openings to pass on the principal zone of cut tiles over the opening. These, and the fundamental assistance affirms close keeping up a basic not too bad ways from weight up level, must be left set up until the strong has had space plan astute to set - for in any occasion 12 hours, and in a perfect world for 24 - or the tiles will sneak by their own one of a kind special excellent weight. When they have been cleared, cut and lit the edges pieces expected to complete the tiling, buttering paste on to the back of each piece before crushing it into spot. To cut edge pieces turn the tile back to front, mark two on the sides of the tiles for the circumstance of the score line and subsequently turn the tile over, score it and break it.
Turning a corner
When turning a corner, fix the crucial vertical line of whole tiles on the going with divider before filling in the cut pieces in the point. With arranged tiles, keep some comparability to structure learning by using cut bits of a close-by tile to fill the openings on each side of the point.
Changes in level
When tiling over existing tiles that stop more than almost the entire far up the divider tile flooring, there is a limit in level to change as indicated by. If the movement is basically nothing, fix the last area of whole tiles with their top edges direct over the improvement, and fill the opening behind with mortar, empowering this to set before keeping fixing whole tiles over the improvement. Steps more than about 12mm basic can't be covered as such. With these you can either stop tiling at the most raised explanation behind the old tiles and fulfillment off the most fundamental inspiration driving the tiling with a hardwood lipping or slips of cut tile set on a level plane, or present a visual break as a dainty wooden rack or the quadrant tiles sold for fitting in the corner between a shower and the divider. The choice is to bring the upper bit of the divider up to a proportionate level - with sheets of MDF or plasterboard, for example.
Grouting
When tiling is done, the going with work is to fill the openings between the tiles with grout. Apply it with a plastic scrubber or a wipe, obliging it well into the gaps between the tiles. Expel riches grout from the covering as mix activates and cloak the grout lines with a sprinkled finger or a little balanced smooth - a used sweet stick is flawless. Make the basic advances not to leave grout to set on the covering as it may be difficult to get off. Unequivocally when the grout has set, clean the tile surface with a perfect, dry surface to finish the progress.
Comments
Post a Comment